How long is the life of a basic round wire coil spring?

Unfortunately, there are no specific test values as reference regarding the life of a round wire coil spring because there is individual difference to a certain extent and the installation conditions are complicated. The usage count varies with the operating temperature, environment, and amount of deformation. To increase the usage count, it is recommended to use the spring up to 70% of the allowable displacement Fmax..

What are the JIS standards for general spring-related materials?

Piano wires: JIS G 3522 Iron wires: JIS G 3532 Hard drawn steel wires: JIS G 3521 Stainless steel wires for springs: JIS G 4313

What influence will the usage without a spring rail have on the spring?

The usage without a spring rail will cause buckling of the spring, bending of its body and other problems, leading to breakage due to high stress locally generated on the inner side of the bending part. To ensure the service life of the spring, install the spring using the shaft, outer diameter guide rail, etc. ※Basically, it is ideal to use the spring on the intermediate shaft of the inner diameter side guide rail, passing it through from the upper surface to the lower surface.

What influence will the usage count of more than 300,000 times beyond the maximum displacement (when used close to the solid length) have on the spring?

The usage count of more than 300,000 times beyond the maximum displacement (when used close to the solid length) will cause high stress breakage above the calculated value on the section. In addition, near the solid length, the effective coil part will gradually get close and the spring constant will increase. Therefore, be sure to use within the allowable displacement Fmax.(mm).

What is the difference between a piano steel wire spring and a hard drawn steel wire spring?

There is little difference in appearance between the two materials. In short, the piano wire is an advanced material, and the hard drawn steel wire is a general material. The piano wire is often used as a spring for precision machinery while the hard drawn steel wire is mostly used as a peripheral spring for groceries or blinds. They are both high-carbon steels with almost the same chemical composition. The production of piano wires is time-consuming and they are expensive because there is additional standardized management and inspection of impurities, the depth of surface scars, and the depth of decarburized layer. Although the subtle difference is invisible to the naked eye, it has a great influence on the quality of the spring.

(!) Since support from Microsoft will end on January 14th, 2020, Windows 7 will be excluded from the recommended environment from December 15th, 2019 on this site. Vì lý do Microsoft kết thúc hỗ trợ cho Windows 7 vào ngày 14/01/2020, Windows 7 sẽ là hệ điều hành không được khuyến khích sử dụng với trang web này từ ngày 15/12/2019.

Tel: 0222-361-1555 Email: [email protected] 8:00 - 17:00 (Mon - Sat)

ものづくりの、明日を支える。MISUMI-VONA 生産材コマースものづくりの、明日を支える。MISUMI-VONA 生産材コマース

Webcode Seach | Series: #CODE

Keyword suggestionsTừ khóa gợi ý

Part number suggestionsGợi ý mã sản phẩm

Discontinued Products

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

[Thông báo] Cập nhật địa chỉ kho tập kết hàng hóa tại khu vực miền Nam của MISUMI Việt Nam. Xem chi tiết.
[Announcement] Update on warehouse address in the Southern region of MISUIMI Vietnam. See more. 
[Cảnh Báo] Thủ Đoạn Lừa Đảo Từ Nhân Viên Giao Hàng – Yêu Cầu Trả Phí Ship. Xem chi tiết.
[Warning] Fraud Calling from Shipper - Asking to Pay Shipping Fee. See more.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

ConfigureTạo

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining SpecificationsĐịnh cấu hình các thông số còn lại

Part Number CompleteĐã hoàn thành

C-UBB16-30

type Free Length L Inner Dia. D-2d (or D) Outer Dia. D (or D1) Height with the max. load applied ([Free Length] – [Allowable Deflection]) Spring Constant Allowable Load (Configurable Range) Max. Load Wire Dia. Total Coils Solid Length Allowable Displacement CAD Days to Ship

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

type
- C-UBB
ClearTrống
Free Length L(mm)
5

10

15

20

25

30

40

60
ClearTrống
Inner Dia. D-2d (or D)(Ø)
2.6

2.7

3.4

3.5

3.8

4

4.2

5.4

5.6

5.8

7

7.2

8

8.4

8.8

9

9.4

11.2

13.6

14.2
ClearTrống
Outer Dia. D (or D1)(Ø)
4

5

6

8

10

12

13

16

20

40
ClearTrống
Height with the max. load applied ([Free Length] – [Allowable Deflection])(mm)
3.75

7.5

11.25

15

18.75

22.5

30

48
ClearTrống
Spring Constant(N/mm)
4.9

9.8

19.6

29.4
ClearTrống
Allowable Load (Configurable Range)(N)
- 4.51~8.50
- 8.51~16.00
- 16.01~30.00
- 30.01~50.00
- 50.01~73.00
- 73.01~107.00
- 107.01~150.00
- 150.01~230.00
- 230.01~580.00
ClearTrống
Max. Load(N)
6.1

12.3

18.4

24.5

36.8

49

61.3

73.5

147

184

196

235

294
ClearTrống
Wire Dia.(Ø)
0.6

0.65

0.7

0.75

0.8

0.9

1

1.1

1.2

1.3

1.4

1.5

1.6

1.8

2.3

2.4

2.5

2.9

3.2
ClearTrống
Total Coils
3.8

4.3

4.8

5.3

6.3

6.6

6.8

7.3

7.5

7.8

8.2

8.3

9.5

9.7

9.8

10.2

10.3

11.3

12.3

13.7

16.8
ClearTrống
Solid Length(mm)
2.9

6.8

6.9

7

9.4

9.5

9.8

9.9

10.2

10.3

10.5

12.4

13.9

14

14.5

14.6

16.1

16.7

20.3

21

27.2

28.2

44.4
ClearTrống
Allowable Displacement(mm)
1.25

2.5

3.75

5

6.25

7.5

10

12
ClearTrống
CADCAD
- 2D
- 3D
ClearTrống

Days to ShipSố ngày giao hàng

Alltất cả các

Same day

8 Day(s) or Less
ClearTrống

Specify AlterationsChỉ định thay đổi

Round Wire Coil Springs, Defection O.D. Referenced, Stainless Steel, Ultra Heavy Load (C-UBB16-30)

Name: Round Wire Coil Springs, Defection O.D. Referenced, Stainless Steel, Ultra Heavy Load
Brand: MISUMI
Price: 16909 VND
Availability: InStock

Click this image to zoom it.Nhấp vào hình ảnh này để phóng to.

Move the mouse over or click the image to zoom

Volume Discount

Check FAQ of this product (5 items)

Brand :

MISUMI

MiSUMi Economy

MISUMI

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

(i)
Caution

thận trọng

**RoHS Compliant is available for some part numbers.
Please contact with MISUMI for detail effective date.
Please check the content on our website as the PDF does not contain the most up-to-date information.

Product Description

This is an economy item, The price is cheaper than the MISUMI standard product.

Economy Round Wire Coil Springs

Heavy Load Sturdy Reliable

- Ultra Heavy Load Capacity for Demanding Applications.

- Prioritizing Outer Diameter Tolerance for Perfect Fit.

- High-Quality Stainless Steel Springs at a Lower Cost

- Ideal for high-load situations with configurable ranges.

- Optimal for extreme conditions and long-term use.

Economy Stainless Steel Knob Type Index Plunger (M8-M10 Thread)

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview

♢When purchasing of Round Wire Springs, please note that this spring is the outer diameter standard type, manufactured with priority to the outer diameter tolerance, and suitable for hole installation occasions.
♢Stainless steel springs are also magnetic. Please be careful.

Dimensional Drawings

Outer Diameter D	φ10 or Less	Free Length L	50 or Less	±1.5mm
	φAbove 12		Above 60	±2.5mm

Material of Round Wire Springs
Material SUS304-WPB Spring Constant ±10%

Specification Table

■C-UBB: Fmax. (allowable displacement) = L×Fa%

The outer diameter standard type gives priority to guaranteeing the outer diameter, while the inner diameter is for reference only.

Type	D－L		d	Solid Length	F max.	N{kgf} max.		Fa%
Type	D－L		d	Solid Length	F max.	N{kgf} max.		Fa%
C-UBB	4－	10	0.65	7.0	2.5	12.3	{1.3 }	25
		15	0.7	10.3	3.75	18.4	{1.9 }	25
		20	0.75	14.4	5	24.5	{2.5 }	25
	5－	5	0.6	2.9	1.25	6.1	{0.63}	25
		10	0.75	6.9	2.5	12.3	{1.3 }
		15	0.8	9.8	3.75	18.4	{1.9 }
		20	0.85	13.4	5.0	24.5	{2.5 }	25
		25	0.9	17.8	6.25	30.6	{3.12 }	25
	6－	10	0.9	6.8	2.5	24.5	{2.5 }	25
		15	1.0	10.5	3.75	36.8	{3.8 }
		20	1.1	14.6	5.0	49.0	{5.0 }
		25	1.1	17.9	6.25	61.3	{6.26 }	25
	8－	10	1.1	6.9	2.5	24.5	{2.5 }	25
		15	1.2	9.9	3.75	36.8	{3.8 }
		20	1.3	14.0	5.0	49.0	{5.0 }
		25	1.3	14.5	6.25	61.3	{6.3 }
	10－	10	1.3	7.2	2.5	24.5	{2.5 }	25
		15	1.4	10.2	3.75	36.8	{3.8 }	25
		20	1.5	13.9	5.0	49.0	{5.0 }
		25	1.5	16.1	6.25	61.3	{6.3 }
		30	1.6	20.4	7.5	73.5	{7.5 }	25
	12－	15	1.5	9.4	3.75	36.8	{3.8 }	25
		20	1.6	12.4	5.0	49.0	{5.0 }
		30	1.8	20.3	7.5	73.5	{7.5 }
	13－	15	1.8	9.5	3.75	73.5	{7.5 }	25
		20	1.9	12.9	5.0	98.1	{10.01}	25
		25	2.0	17.0	6.25	123	{12.55}	25
		30	2.1	20.5	7.5	147	{15.0}	25
		40	2.3	28.2	10.0	196.0	{20.0}	25
		60	2.5	44.4	12	235	{24.0}	20
	16－	20	2.1	12.1	5.0	98.1	{10.01}	25
		30	2.4	21.0	7.5	147.0	{15.0}	25
	20－	25	2.9	16.7	6.25	184.0	{18.8}	25
		40	3.2	27.2	10	294	{30.0}	25
		60	3.5	44.6	12.0	353.0	{36.02}	25

The outer diameter standard type gives priority to guaranteeing the outer diameter, while the inner diameter is for reference only.

The solid length is a reference value. There will be slight differences among batches.

Be sure to use within the allowable displacement Fmax.(mm).

The number of laps is a reference value. There will be slight differences among batches.

kgf (load)=N/mm (spring constant)×0.101972×F (displacement)
{kgf}=N×0.101972

■Spring Constant The spring constant

D12 is for C-UY・C-UR・C-UF・C-UBB only. D14 is for C-UBB only.

Type

C-UV

C-UY

C-UR

C-UF

C-UL

C-UTT

C-UM

C-UH

C-UBB

0.05{0.005}

0.2{0.02}

0.3{0.03}

0.5{0.05}

N/mm
0.05
{kgf/mm}{0.005}

N/mm
0.098
{kgf/mm}{0.01}

N/mm
0.29
{kgf/mm}
{0.03}

N/mm
0.49
{kgf/mm}
{0.05}

N/mm
0.98
{kgf/mm}
{0.1}

1.5{0.15}

2.0
{0.2}

2.9{0.3}

4.9{0.5}

N/mm
2.0
{kgf/mm}
{0.2}

N/mm
2.9
{kgf/mm}
{0.3}

N/mm
5.9
{kgf/mm}
{0.6}

N/mm
9.8
{kgf/mm}
{1.0}

N/mm
0.2
{kgf/mm}
{0.02}

N/mm
9.8
{kgf/mm}
{1.0}

N/mm
19.6
{kgf/mm}
{2.0}

0.3{0.03}

0.5{0.05}

0.98{0.1}

2.9{0.3}

3.9{0.4}

4.9{0.5}

14.7{1.5}

29.4{3.0}

Fmax.

F＝L×70％

F＝L×75％

F＝L×60％

F＝L×45％

F＝L×40％

F＝L×35％

F＝L×30％

F＝L×25％

Product Feature

Different from ordinary springs on the market, MISUMI Round Wire Springs are more precise and refined, divided into the inner diameter standard type and the outer diameter standard type, the former of which is manufactured givingpriority to the inner diameter tolerance while the latter is manufactured giving priority to the outer diameter tolerance.

Select an appropriate Round Wire Springs type according to the actual installation situation, and refer to the published content for the specific inner and outer diameter tolerance values.
* The solid length is a reference value. If it is used under the limit condition of the solid length, the spring may be deformed, or damaged after using only a limited number of times. Therefore, use within the allowable displacementFmax.(mm).
To increase the usage count, it is recommended to use the spring up to 70% of the allowable displacement Fmax..

Installation Diagram of Outer Diameter Standard Type Round Wire Coil Spring

Example of Use

Hole Reference Positioning Mechanism
A Round Wire Springs is mechanism for positioning the workpiece based on the hole reference.
Loosening during positioning can be reduced by using a tapered pin to eliminate the deviation caused by the tolerance of each workpiece hole. Select the compression spring to move from the beginning of the positioning contact with the workpiece.

Precautions

Precautions for use of Round Wire Springs
Operating temperature of Round Wire Springs
SWP-A……Normal temperature (0~40℃)
Stainless steel……-10~100℃
Spring oil tempered steel wire……Normal temperature (0~40℃)
*If the spring is used under conditions exceeding the above temperature, the load value may decrease due to usage conditions.
*When used in an environment with high and low temperature differences and humidity such as outdoors, it is recommended to choose stainless steel products.
* Heat-resistant springs can also be used. For details, refer to the Plastic Mold Components Catalog.
Stainless steel springs are also magnetic. Please be careful.

Related Products


(Economy series) Round Wire Springs - Outer Diameter Standard Stainless Steel, Light Load, Spring Constant 0.5 to 3.9 N/mm	(Economy series) Round Wire Springs - Inner Diameter Standard Stainless Steel, Light Load, Spring Constant 0.29 to 0.49 N/mm	(Economy series) Round Wire Springs - Outer Diameter Standard Stainless Steel, Heavy Load, Spring Constant 2.0 to 14.7 N/mm
Reason for Recommendation: MISUMI Basic Round Wire Springs, Outer Diameter Standard Type, Light Load Type	Reason for Recommendation: MISUMI Basic Round Wire Springs, Inner Diameter Standard Type, Light Load Type	Reason for Recommendation: MISUMI Basic Round Wire Springs, Outer Diameter Standard Type, Heavy Load Type

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.Incomplete part number.
Please use left hand selections to complete a part number.

Loading...Tải…

: 30; 45; 60

Part Number
C-UBB16-30

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to ShipSố ngày giao hàng	Free Length L (mm)	Inner Dia. D-2d (or D) (Ø)	Outer Dia. D (or D1) (Ø)	Height with the max. load applied ([Free Length] – [Allowable Deflection]) (mm)	Spring Constant (N/mm)	Allowable Load (Configurable Range) (N)	Max. Load (N)	Wire Dia. (Ø)	Total Coils	Solid Length (mm)	Allowable Displacement (mm)
	16,909 VND	1 Piece(s)	Available	Same day	30	11.2	16	22.5	19.6	107.01~150.00	147	2.4	7.8	21	7.5

Loading...Tải…

Basic InformationThông tin cơ bản

Material	SUS304-WPB	End Surface Status	With Grinding

Please check the type/dimensions/specifications of the part C-UBB16-30 in the Round Wire Coil Springs, Defection O.D. Referenced, Stainless Steel, Ultra Heavy Load series.Vui lòng kiểm tra kiểu/kích thước/thông số kỹ thuật của phần C-UBB16-30 trong chuỗi Round Wire Coil Springs, Defection O.D. Referenced, Stainless Steel, Ultra Heavy Load.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer toCác thông số kỹ thuật và kích thước của mã sản phẩm có thể không được bao phủ đầy đủ. Để biết chi tiết chính xác, hãy tham khảo manufacturer catalogsdanh mục nhà sản xuất ..

Frequently asked question (FAQ)FAQ

Question:Question: How long is the life of a basic round wire coil spring?: Answer:Answer: Unfortunately, there are no specific test values as reference regarding the life of a round wire coil spring because there is individual difference to a certain extent and the installation conditions are complicated.
The usage count varies with the operating temperature, environment, and amount of deformation. To increase the usage count, it is recommended to use the spring up to 70% of the allowable displacement Fmax..
Question:Question: What are the JIS standards for general spring-related materials?: Answer:Answer: Piano wires: JIS G 3522
Iron wires: JIS G 3532
Hard drawn steel wires: JIS G 3521
Stainless steel wires for springs: JIS G 4313
Question:Question: What influence will the usage without a spring rail have on the spring?: Answer:Answer: The usage without a spring rail will cause buckling of the spring, bending of its body and other problems, leading to breakage due to high stress locally generated on the inner side of the bending part. To ensure the service life of the spring, install the spring using the shaft, outer diameter guide rail, etc.
※Basically, it is ideal to use the spring on the intermediate shaft of the inner diameter side guide rail, passing it through from the upper surface to the lower surface.
Question:Question: What influence will the usage count of more than 300,000 times beyond the maximum displacement (when used close to the solid length) have on the spring?: Answer:Answer: The usage count of more than 300,000 times beyond the maximum displacement (when used close to the solid length) will cause high stress breakage above the calculated value on the section. In addition, near the solid length, the effective coil part will gradually get close and the spring constant will increase. Therefore, be sure to use within the allowable displacement Fmax.(mm).
Question:Question: What is the difference between a piano steel wire spring and a hard drawn steel wire spring?: Answer:Answer: There is little difference in appearance between the two materials. In short, the piano wire is an advanced material, and the hard drawn steel wire is a general material.
The piano wire is often used as a spring for precision machinery while the hard drawn steel wire is mostly used as a peripheral spring for groceries or blinds.
They are both high-carbon steels with almost the same chemical composition. The production of piano wires is time-consuming and they are expensive because there is additional standardized management and inspection of impurities, the depth of surface scars, and the depth of decarburized layer.
Although the subtle difference is invisible to the naked eye, it has a great influence on the quality of the spring.

Check other FAQ (2 items) HideĐóng.

Products like this...

Part Number
C-UBB12-15
C-UBB12-20
C-UBB12-30
C-UBB20-25
C-UBB20-40
C-UBB4-10

Standard Unit Price	Minimum order quantity	Volume Discount	Days to ShipSố ngày giao hàng	Free Length L (mm)	Inner Dia. D-2d (or D) (Ø)	Outer Dia. D (or D1) (Ø)	Height with the max. load applied ([Free Length] – [Allowable Deflection]) (mm)	Spring Constant (N/mm)	Allowable Load (Configurable Range) (N)	Max. Load (N)	Wire Dia. (Ø)	Total Coils	Solid Length (mm)	Allowable Displacement (mm)
7,389 VND	1 Piece(s)	Available	Same day	15	9	12	11.25	9.8	30.01~50.00	36.8	1.5	5.3	9.4	3.75
8,682 VND	1 Piece(s)	Available	Same day	20	8.8	12	15	9.8	30.01~50.00	49	1.6	6.8	12.4	5
11,046 VND	1 Piece(s)	Available	Same day	30	8.4	12	22.5	9.8	73.01~107.00	73.5	1.8	10.3	20.3	7.5
19,652 VND	1 Piece(s)	Available	Same day	25	14.2	20	18.75	29.4	150.01~230.00	184	2.9	4.8	16.7	6.25
34,641 VND	100 Piece(s)		8 Day(s)	40	13.6	40	30	29.4	230.01~580.00	294	3.2	7.5	27.2	10
5,258 VND	1 Piece(s)	Available	Same day	10	2.7	4	7.5	4.9	8.51~16.00	12.3	0.65	9.8	7	2.5

Top of the page

About MISUMIVề Misumi

About this WebsiteVề trang Web này

Useful ToolsCác công cụ hữu ích

Customer ServiceDịch vụ chăm sóc khách hàng

MISUMI Contact Monday to Saturday: 8:00 am - 5:00 pm Order cut off time is 5:00 pm Thứ 2 đến Thứ 7: 8 giờ sáng đến 5 giờ chiều Hạn chót đặt hàng là 5 giờ chiều

Tel:Số điện thoại:0222-361-1555
Fax:Số Fax:0222-361-2555
InquiryYêu cầu

MISUMI APP

Install MISUMI APP

MISUMI Vietnam Company Limited, Legal Representative: Tomohiro Watanabe,
phone: 0222-361-1555, e-mail: [email protected], Enterprise Code: 0107514576,
Date of Issuance: 22 July 2016, Place of Issuance: Bac Ninh, Business Certificate No. 6573041568-KD dated 27 September 2016 issued by the People's Committee of Bac Ninh

Công ty TNHH MISUMI Việt Nam, Đại diện theo pháp luật: Tomohiro Watanabe,
Điện thoại: 0222-361-1555, e-mail: [email protected], Mã số doanh nghiệp: 0107514576,
ngày cấp 22/7/2016, nơi cấp: Bắc Ninh, Giấy phép kinh doanh số: 6573041568-KD ngày cấp 27/9/2016 bởi UBND tỉnh Bắc Ninh

Search by Category / Brand Tìm theo danh mục, nhãn hiệu

Search by Category Tìm theo danh mục

How can we improve?

ConfigureTạo

Specification/DimensionsĐặc điểm kỹ thuật / Kích thướcĐặc điểm kỹ thuật / Kích thước

type

Free Length L(mm)

Inner Dia. D-2d (or D)(Ø)

Outer Dia. D (or D1)(Ø)

Height with the max. load applied ([Free Length] – [Allowable Deflection])(mm)

Spring Constant(N/mm)

Allowable Load (Configurable Range)(N)

Max. Load(N)

Wire Dia.(Ø)

Total Coils

Solid Length(mm)

Allowable Displacement(mm)

CADCAD